Mold Structure encyclopaedias

Mold structure encyclopaedias

Sositar mould have more than 15 years in mold manufacture field,and accumulate lots of experience in mold design and mold making process, to help the new entrants and our customers to understand mold better,we list some mold animation as below:

  1. three plates mold

This is a a popular design for mold,the advantage is :we can make more than one gate for molding,and can place the point gate in the center of product.

2)  insert mold

Ussaully we can molding steel pieces, copper nut, screws in plastic for some special use

3) mold with lifters

Lifter is use to release the undercut in product

4)mold with submarine gate

Submarine gate mark is very small,so we can place the gate on product surface and the mold can full automotively.

5)submarine on ejectors

when we can not find a good position for gate,we make cut the ejectors and put the gate there

6) hot runner mold

Hot runner can save the material for runner,reduce the cycle time and improve the production quality

7) thread release mold

the core will retote itself and release the thread

8)mold with sliders

slides for the under release

9,mold for hubs

10)sleeve ejectors

Sleeve ejector is a good solution for long bosses which have a hole in the center

if you would like to find a professional plastic mold manufacturer in China,please contact us,I am sure our service will satisfy you


Mold Trial Instruction

First, introduction
When we receive a new mold test mould proofing needs, we are always keen to try out an earlier result of prayer request and smooth so as not to waste hours of work and cause trouble.
But in this we have to remind two points: first, the mold designers and manufacturing engineers sometimes an error in our test model, fails to alert small error may arise due to large damage. Second, the test model results is to ensure the successful future production. If the tryout process did not follow reasonable steps and make the appropriate records, that is no way to guarantee the smooth progress of mass production. We also emphasize that “the use of smooth, then mold will quickly increase the profits of the recovery, otherwise the cost of damage caused by even more than the mold itself will cost.”

Second, try this before you mold on the machines
1. Relevant information about mold:
Can achieve the best mould design drawings, detailed to the analysis, and sometime have mold technician to participate in the work.

2. The first stage in the work of the mechanical inspection with the action:
Should pay attention to whether the cuts, missing pieces and loose phenomena, mode to the slide action is really, waterway and airway joints with or without leakage, mold opening process, then if restrictions should also be marked in the model. If these actions before the model was done in the hanging, that would be found to avoid problems linked to mold, mold removal go to waste hours of work have taken place.
3. When the proper action after determining mould ministries, we must select the appropriate test mold injection molding machine, the choice should pay attention to

  •  Injection capacity
  • the width of guide bar
  • the largest open range
  • are complete and other accessories

All confirmed that no problems were hanging next step is to mold, hanging in the lock should pay attention to all the templates folder and mold do not remove the fish before the hanging, in order to avoid loosening or breakage of the template folder so that die fall.
Mold should be carefully re-installed after inspection mold all the parts of mechanical movement, such as skateboarding, thimble, back tooth structure and limit switches of action really. And pay attention to Shoot mouth is aligned with the inlet. The next step is to pay attention to clamping action, then the pressure should be lowered off mode, in manual and low clamping action in attention and listen to see whether there is any different from time to smooth movement and sound and so on.

4. Raise the mold temperature:
Based on raw materials used in product performance and die size of the choice of appropriate mold temperature control unit will die when the temperature increased to produce the required temperature. Once the mold temperature increased again after the view to the various parts of the action, because the steel due to thermal expansion, may lead to card mode phenomenon, it should be noted that the sliding ministries in order to avoid strain and vibration generation.

5. If the pilot scheme is not implemented within the factory rules, we propose to adjust the conditions of a test mode a condition can only be adjusted in order to distinguish one effect of changes in the terms of the finished product.

6. According to different raw materials, on the appropriate use of the original Tu-made baking.

7. Tryout with the future production using the same raw materials as possible.

8. Do not totally inferior race tryout material, if the color needs to be arranged test color.

9. Internal stress and other issues often affect the secondary processing, should be finished after the tryout to be stable after secondary processing of slow closed mold, the mold should be fine off the pressure and movement several times to see whether the co- mold pressure inequality and to avoid distortion product generated flash and mold.

After checking the above steps are then die off die off speed and the pressure reduced, and the security buckle ejection rod and set a good trip, and then transferred to a normal off mode and off mode speed. If the trip involves the maximum limit switch should be adjusted to shorter mold stroke, in which cut off the mold before the maximum travel speed mold action. This is because the put on the mold during the trip among the high-speed movements who travel longer than the low speed of it. Mechanical machine in the plastic top of the bar must also be adjusted after the full opening-mode action role, so that thimble board or peel board Stress and deformation.

In the first model for injection before you re-check the following:

  • whether the feeding schedule is too long or less
  • the pressure is too high or too low
  • whether the filling too fast or too slow speed
  • processing cycle is too long or too short

To prevent the finished short shot, broken, deformed, or even hurt mold flash. If the processing cycle is too short to wear a thimble to the top ring Jishang finished products or peeling. Such circumstances may cause you to spend 23 hours to remove the finished product. If the processing cycle is too long, then the mold core of the thin rubber parts may tighten and broken, of course, you can not expect tryout process might happen, but do take account of prior and timely measures will help you avoid serious and costly damage.

Third, the main steps tryout
In order to avoid unnecessary waste of production time and when disturbed, indeed, necessary to pay the patience to adjust and control various processing conditions, and find the best temperature and pressure conditions, and develop standard procedures for test mode and available and in establish a regular working methods.

1. View the barrel of the plastic material is correct, and whether in accordance with the provisions of baking, (test mode and production of different raw materials if it might yield different results).

2. Feed tube to ensure thorough cleaning to prevent bad solution, or miscellaneous material rubber injection mold, plastic materials and hybrid solution because of inferior materials may be mold stuck. Test tube temperature and mold temperature of raw materials for processing.

3. To adjust pressure and injection volume in order to produce a satisfactory finished appearance, but can not run flash in particular, there are some not yet fully solidified cavity when finished, before the adjustment of various controlled conditions should think about, because the filling rate slightly changes may lead to changes in very large filling.

4. To be patient until the conditions of machines and molds to stabilize, that is, medium-sized machines may have to wait more than 30 minutes. Can use this time to see the finished product problems that might arise.

5. Screw forward time can not be shorter than the plastic gate solidification time, otherwise the product will reduce the loss of weight and performance of finished products. And when the mold is heated screw forward time for compaction should also be extended discretion of finished products.

6. Reasonable adjustments to reduce the overall processing cycle.

7. Redeployment of the conditions of the new operation at least 30 minutes, stabilize, and then continuous production of at least a dozen products all look in their bowl marked date, number, and press cavity were placed in order to test the stability of the exact operation and export the reasonable control of tolerance. (Particularly valuable for multi-point die).

8. Will continuously measure and record the significant sample size (such samples should be cooled to room temperature and then volume).

9. The amount of each product may look like the size to make a comparison, should be noted:

  • the stability of size.
  • whether there are certain size has increased or decreased while still showing a change in processing conditions, such as poor temperature control or hydraulic control.
  • whether movements in size within the tolerance range.

10. If not quite finished size of changes in processing conditions are normal, you need to see if each cavity of the finished product its quality can be accepted, its size can be within the tolerance allowed. To measure out more or less continuous average cavity number down to check whether the correct size of the mold.

Record and analyze data in order to modify the tooling and production as conditions require, and for the future reference for mass production.

  1. To make a longer processing time of operation to stabilize the melt temperature and hydraulic oil temperature.
  2. By all the finished size is too large or too small to adjust the machine conditions, if the shrinkage appears to shoot too much and finished less than expected, also available for reference in order to increase the gate size.
  3. The cavity size is too large or too small to be amended, if the cavity size and the door is still correct, then the candidate to change the machine conditions, such as filling rate, mold temperature and pressure, ministries, and view some of the mold Point is filling slowly.
  4. In accordance with the finished product of the cavity mold core shift with circumstances or be modified individually, perhaps try transfer mold filling rate and temperature, in order to improve its uniformity
  5. Check and modify the injection machine malfunction, such as pumps, oil valves, temperature controllers, etc. will lead to adverse changes in processing conditions, even more perfection in the maintenance of the mold can not be bad to play a highly efficient machine. In reviewing the records of all values, the retention of a sample compared to proofread the sample after it has been amended to improve.

Fourth, important issues
Keep all samples in the tryout process inspection records, including the processing cycle, all kinds of pressure, melt and mold temperature, tube temperature, injection movement time, screw feeding time, etc., in short, should help to save all future was able to successfully create the same conditions of data processing in order to obtain the products meet quality standards.

The plant is often overlooked when testing mold mold temperature, and in the short-term production test mode and in the future when the mold temperature is the most difficult to master, rather than the correct sample of the mold temperature can affect the size, brightness, shrinkage, flow lines, and less material phenomena If no mold temperature controller to hold in the future when production problems occur.

Industrial innnovation:plastic injection molding

OEMs make their own products from molds that allow them to create their own original product designs. However, as a matter of fact, OEMs are not the real originals. All in all, even OEMs need to outsource injection molds from factories which will build the molds for them.


Currently, there are factories which make injection mold tooling for plastic products. For a diversity of industries, plastic injection molding is of great importance, and the more quickly and more effectively they can mold these products, the faster and more efficient their production can be. A great number of industries, ranging from medical care to food service, are dependent on machines with plastic injection products, so as to get their jobs well done on a day-to-day basis. What is critically important for those plastic molding factories is that they have to think about what the specific needs for each specific part are. For example, they have to consider not only the hardness of the plastic material, but also the ideal temperature for melting the plastics, as well as the type of plastic that is used for every individual end product. Only then will the parts be manufactured with the highest standards.


During the injection molding process, plastic granules are fed into the injection chamber through a hopper. A reciprocating screw is used inside the chamber to guarantee the even distribution of these plastic granules, which are then moved into a heater and melted, so that it is able to flow into the clamping chamber. The plastic material is evenly fed first into the mold cavity, and then into the mold, where a moveable plate clamps it into the mold. Under certain temperature and pressure conditions, the plastic is hardened and molded into the desired parts.


When plastic injection molding is mentioned in a conversation, not all products are produced in an equal manner. There are some tasks that are designed to mold smaller parts, while some others are carried out to mold larger parts. The appearance of plastic injection molding has brought about a revolution to the world industry. Being able to use plastics to produce parts hard enough for machines has made it a lot easier to manufacture parts more quickly and more efficiently than ever before. In some particular cases, plastic parts even perform better than the metal ones. Whether the plastic molding process is the right solution for your business? Well, it is dependent on whether you think it would be appropriate for your application. At least, it would be good for you to gather a little more information about the process, so that you will get to know how to manufacture an up-to-standard quality part.

Proper Quality Management Extends Tool Service Life

Proper Quality Management Extends Tool Service Life

In the production process, tools are subject to normal wear and tear. It is certain that quality management control in daily production will play an important role in the assurance of tool quality, which mainly covers the following aspects:

  1. Effective data management, including production data, process data and drawing documents: Effective management of production data, process data and 2D/3D drawing documents is able to ensure a complete document library and full drawing versions, leading to effective sharing and effective inquiry of the drawings. In the Engineering Dept., if a PC database with a complete document management system is not able to be established, and there’s no one to collect and organize those previously scattered drawings, it will lead to data chaos and inconsistency which will probably affect all the design files, including 2D/3D drawings, original data, design change/maintenance history and 3D models, etc. Without standardized 2D CAD drawings, great problems will occur. Because of this confusion in data management, it is difficult to identify problems and then correct them promptly, causing tools to be modified and repaired, not to mention the addition of tool manufacturing costs and the extension of tool production cycle.
  2. Maintain data consistency and integrity, including tool drawings and processes, etc.: Make use of effective, sophisticated and strict test measures to ensure that tool drawings, production processing technologies and the alike are consistent and integral.
  3. Collect and record the manufacturing costs of each set of the tools in time: It is recommended that the workshop takes effective management control measures to find out obsolete tools in time; uses accurate, efficient and accurate processing technologies to design die structures for tooling parts and parts testing. This will effectively reduce the changes in mold design. As a result, the maintenance, actual costs, as well as the quality of each of the mold produced will be effectively controlled.
  4. Labor force planning: When all the elements of mold production can be organically organized and integrated, such as the information of planning, design, processing technology, production scheduling and labor resources, it will be much easier to effectively coordinate the production projects, thus effectively guarantee the quality and timely delivery of mold products.
  5. Development of a comprehensive and practical tool production management system: Develop a complete manufacturing management system, including implementation of manufacturing management processes, product data management, process data management, project management, production scheduling management, computer information management, tool production planning, tool design, process development, product testing assignment, workshop management, warehouse management, as well as other related information management. Complete the development in a well-planned way, to realize a comprehensive delivery tracking management system in the end.
  6. Establish a full failure mode and effects analysis system: Establish a failure mode and effects analysis system for tool design and manufacturing by means of meetings, bulletins, computer sharing, as well as incentive methods, so as to prevent the same problems from happening again in the future.